5iMX.com 我爱模型 玩家论坛 ——专业遥控模型和无人机玩家论坛（玩模型就上我爱模型，创始于2003年）

标题: 国外牛人做的V8发动机-简直太假了！！！！！ [打印本页]
作者: 茉莉素馨    时间: 2012-8-10 05:21
标题: 国外牛人做的V8发动机-简直太假了！！！！！
这是从youtube上下 载下来的视频，发在优酷上
看起来已经批量化生产了，太精致了！！！

看资料，这个发动机，最高9000转，预计正常5.5马力，增压最高9马力
可以参考这个网站的介绍：http://www.tech-domain.com/thread-7395-1-1.html


http://v.youku.com/v_show/id_XNDM3Mzk4OTM2.html
视频截图：

[ 本帖最后由 茉莉素馨 于 2012-8-10 17:02 编辑 ]
作者: 茉莉素馨    时间: 2012-8-10 05:48
高清版本的正在上传，晚些时候发上来。


高清下 载地址
http://www.rayfile.com/zh-cn/files/00b5f591-e29e-11e1-819f-0015c55db73d/

[ 本帖最后由 茉莉素馨 于 2012-8-10 15:31 编辑 ]
作者: 茉莉素馨    时间: 2012-8-10 05:48
google上找到的一点资料，E文好点的模友给翻译一下吧：



     Unfortunately, the 427 engine that many of you have been so familiar with, is no longer in production. Like the V-10, most of the molds for the 427 engine were destroyed in a catastrophic fire at the foundry.
     
Here is the latest in the Conley line of V-8 engines. It sports the Stinger 609 name badge (6.09 cubic inches or almost 100 cc) and is the culmination of almost 30 years of knowledge gained in the designing and construction of model engines.
The new Stinger possesses no parts used in prior V-8 engines.

The bore is 1.00, with a .970 stroke. It weighs about 11.25 pounds and measures approximately 14" long (from the front timing belt to the end of the transmission), 6" wide, and 8-1/4" tall. The supercharged version will be about 10" tall.
Among the numerous innovative features like large oval shaped intake ports, "D" shaped exhaust ports, and investment cast parts, two bold attributes stand tall: the dry sump pressurized oiling system and a full ignition system. The engine even has a user replaceable oil filter.
For those of you who lack familiarity with dry sump oiling, it simply means that oil resides in a holding tank, rather than a conventional oil pan, which circulates throughout the engine.
The oil that does collect in the pan is simply pumped back to the holding tank. I have incorporated what is call a "three stage" oil pump to move all the oil. One stage is used to feed oil to the engine, whereas, the other two stages are used to remove all the accumulated oil from the pan. This is particularly important for high acceleration, cornering, or boat applications. An important side note, my test engine held about 20 lbs oil pressure at idle and 60 lbs oil pressure at 9,000 rpm.
The dry sump oiling system not only adds more oil volume but aids in engine cooling and makes sure that there is plenty of oil during hard acceleration or sharp corners. The spark plugs have a 10-40 thread. As always, the new Stinger 609 V-8 will have an electric starter as standard equipment. No hand held electric motors here, or something that fits in a box below the engine, but rather a 12 volt electric motor that is an fundamental part of the engine. It can be activated manually or via the transmitter on your remote control. The centrifugal clutch is also included. The cost of the standard engine is $5,695.00 and will show off the standard “Zoomie” style exhaust. At the present time here is a list of the options:
Exhaust manifolds, cast in 303 stainless steel......................$   279.00
Exhaust manifolds, cast in 303 stainless steel - polished ....$   559.00
Painted Valve covers and intake manifold.............................$   125.00
Supercharger installed and tested..........................................$1,695.00
High duration camshaft (installed at factory only)................$   279.00
Transmission with forward-neutral-reverse available in near future.

Each engine will be fully tested and adjusted for optimum performance. I am expecting around 5.5 hp at 9,500 rpm for the normally aspirated version and about 9 hp for the supercharged version.
Prices start at$5,695.00
            for the non supercharged version,
plus shipping and handling.
Prices are subject to change without notice.


[ 本帖最后由 茉莉素馨 于 2012-8-10 16:47 编辑 ]
作者: 新新8    时间: 2012-8-10 08:07
:em26:
作者: aband    时间: 2012-8-10 08:50
太帅了　DIY发动机也是我的梦想
作者: gaifeng640909    时间: 2012-8-10 08:56
标题: 回复 楼主 茉莉素馨 的帖子
不是，你这标题是？？？太假了是啥意思。
作者: 茉莉素馨    时间: 2012-8-10 11:03
标题: 回复 6楼 gaifeng640909 的帖子
哦~ 算方言吧~ 就是吊爆了~
作者: aband    时间: 2012-8-10 11:54
楼主　YOUTUBE视频用什么工具下的
作者: 茉莉素馨    时间: 2012-8-10 15:32
标题: 回复 8楼 aband 的帖子
用的这个~
作者: fatumai    时间: 2012-8-10 18:15
确实很精致，估计运作很平顺！
作者: stevekk2012    时间: 2012-8-10 22:56
中 国也应该有这样的模友呀，强，
作者: mozhiqi    时间: 2012-8-15 13:05
很强大，我们中 国也有人在制造，只是最近没更新，不知为什么！
作者: mygod0218    时间: 2012-8-16 23:32
牛暴了！
作者: anquan_lb    时间: 2012-8-17 14:23
中 国做有图吗，有的话顶起来呀！

[ 本帖最后由 anquan_lb 于 2012-8-17 14:26 编辑 ]
作者: johniu    时间: 2012-8-17 16:09
实在够牛啊
作者: zhai_7    时间: 2012-8-20 11:44
再顶:em14::em15:
作者: 怒海蛟龙    时间: 2012-8-20 21:33
:em07:
作者: fuleiming    时间: 2012-8-21 18:51
:em26: :em26:
作者: kafuka    时间: 2012-8-24 13:47
强暴·······



欢迎光临 5iMX.com 我爱模型 玩家论坛 ——专业遥控模型和无人机玩家论坛（玩模型就上我爱模型，创始于2003年） (http://wz.5imx.com/) Powered by Discuz! X3.3