有史以来能干活最小的 炮塔铣

christzyy

以前我发过家用型的 那这个应该算模型级的了 真佩服国人 也不知道鬼佬怎么得到的 现在卖380美元 价格挺不错的 可惜在地球的另一边:em15:

http://cgi.ebay.com/Small-Bench-Milling-Machine-/230531141009?pt=LH_DefaultDomain_0&hash=item35acba0d91

Mill made in Taiwan in 1984.  I have used it for milling aluminum, brass, and various plastics.  I have now acquired a larger vertical mill as I will be milling steel.  It is a compound mill as it tilts +/- 30 degrees foward and back, tilts sideways  +/- 30 degees, and the X table can be turned by +/- 45 degrees.  The mill head has 4" of back and foward travel.
Motor is 2 HP wired for 115 volts with a maximum current of 12 amps.  The motor has been rewound and required the pressing of two switches to start it.
The mill operates smoothly and I have had No problems with it in the three years that I have owned it.
Collet size is R8 the same as for a Bridgeport and most newer mills.
Table size 19.5"X 5"
X travel  10"
Y travel     7"
Z travel quil  2.5"
Z travel column 7"
Maximum height from collet to table is 9"

1984年在台湾制造机。I have used it for milling aluminum, brass, and various plastics.我已经用它来加工铝、黄铜、各种塑料产品。I have now acquired a larger vertical mill as I will be milling steel.我已经获得了更大的立磨我将铣削钢。It is a compound mill as it tilts +/- 30 degrees foward and back, tilts sideways +/- 30 degees, and the X table can be turned它是一种复合机为它倾斜+ / - 30度,一边倾斜,提出+ / - 30 degees、X表可以转by +/- 45 degrees.通过+ / - 45度。The mill head has 4" of back and foward travel.磨坊头有4”的提出旅游。
Motor is 2 HP wired for 115 volts with a maximum current of 12 amps.电机为115伏2点兴奋与电流安培的12个。The motor has been rewound and required the pressing of two switches to start it.电机已被当场而紧迫的两个开关启动它。
The mill operates smoothly and I have had No problems with it in the three years that I have owned it.工厂运转平稳,我没有问题的三年里,我拥有它。
Collet size is R8 the same as for a Bridgeport and most newer mills.R8的大小是夹同一Bridgeport和大多数新工厂。
Table size 19.5"X 5"工作台面积195“X”
X travel 10"10“X旅行
Y travel 7"7“Y旅行
Z travel quil 2.5"quil Z旅行2.5吋的。
Z travel column 7"Z旅游专栏7 "
Maximum height from collet to table is 9"最大的高度,桌子是9 "夹

[ 本帖最后由 christzyy 于 2010-9-28 19:47 编辑 ]

christzyy

沙发自己的 就这么几张图 以后发现其他的会补上来

家用炮塔铣链接 http://bbs.5imx.com/bbs/viewthread.php?tid=378648&extra=&highlight=%C5%DA%CB%FE%2Bchristzyy&page=1

[ 本帖最后由 christzyy 于 2010-9-28 19:46 编辑 ]

liulei000

这个怎么能叫炮塔铣床？

VINTAGE30

脑袋 好大 啊

CXZ子敬

唉，可惜在地球那一边。

christzyy

原帖由 liulei000 于 2010-10-1 10:44 发表
这个怎么能叫炮塔铣床？

那什么叫炮塔铣床:em22:

闲云孤鹤

这个顶多算个大头铣。。。。。:em15:

星火

哪里的jj呀
！！！！！！！！！

田螺

这么早的帖子都翻出来，真不容易。

ansonchina

大的叫炮，小的叫抢
你这个应该叫抢塔铣

zihe98

嗯，好的话开模铸造

ygh