为什么我使用的artcamA轴刀路总是雕刻不成,望高手指点

gold110

那位高手帮我看一下，我用的是ArtCAM 2008输出A轴程序的，在雕刻的时候只是走一个槽而已，我的A轴是平行X轴用的是4轴驱动器在MACH3里设置了对应的脉冲,不知道问题出现在那里望高手多多指点









雕刻的时候总是缘着蓝色的线走刀,只雕刻出条线
G代码如下
G90G0G59G40G17
T1M6
S50000M3
G0 X0.0000 Y0.0000 Z2.1336 A0.000 F2000
G0  X0.0254 A0.1029 Z2.1336
G1  Z-22.3410 F1000
G1  X0.0720 A0.2914 F1500
X88.8746 A359.8972
X88.8280 A359.7086
X0.0254 A0.1029
X0.0720 A0.2914
X88.8746 A359.8972
X88.8280 A359.7086
X0.0254 A0.1029
X0.0720 A0.2914
X88.8746 A359.8972
X88.8280 A359.7086
X0.0254 A0.1029
X0.0720 A0.2914
X88.8746 A359.8972
X88.8280 A359.7086
X47.2906 A191.5029
X45.8004 A185.4686 Z-22.3566
X44.0309 A178.3029 Z-22.3671
X41.6094 A168.4971 Z-22.3410
X27.9654 A113.2457
X14.3679 A58.1829
X0.8170 A3.3086
X0.0254 A0.1029
X0.0720 A0.2914
X40.8178 A165.2914
X41.7491 A169.0629 Z-22.3465
X43.6584 A176.7943 Z-22.4058
X44.9622 A182.0743 Z-22.4111
X46.9180 A189.9943 Z-22.3586
X47.6631 A193.0114 Z-22.3424
X60.0033 A242.9829 Z-22.3410
X73.2282 A296.5371
X85.1958 A345.0000
X88.8746 A359.8972
X88.8280 A359.7086
X48.9204 A198.1029
X48.0822 A194.7086 Z-22.3626
X46.5921 A188.6743 Z-22.4532
X45.2416 A183.2057 Z-22.4973
X43.9378 A177.9257 Z-22.5004
X42.5408 A172.2686 Z-22.4611
X40.9575 A165.8571 Z-22.3680
X40.0262 A162.0857 Z-22.3410
X27.3600 A110.7943
X13.5297 A54.7886
X1.3293 A5.3829
X0.0254 A0.1029
X0.0720 A0.2914
X39.4674 A159.8229
X40.9109 A165.6686 Z-22.4321
X42.2148 A170.9486 Z-22.5164
X43.6118 A176.6057 Z-22.5640
X45.0088 A182.2629 Z-22.5693
X46yue4ri058 A187.9200 Z-22.5321
X47.8028 A193.5771 Z-22.4514
X49.3861 A199.9886 Z-22.3428
X61.6331 A249.5829 Z-22.3410
X74.8580 A303.1371
X86.8257 A351.6000
X88.8746 A359.8972
X88.8280 A359.7086
X50.0846 A202.8171
X49.4326 A200.1771 Z-22.3682
X48.0822 A194.7086 Z-22.4960
X46.7318 A189.2400 Z-22.5817
X45.3348 A183.5829 Z-22.6279
X43.9378 A177.9257 Z-22.6323
X42.5408 A172.2686 Z-22.5956
X41.1903 A166.8000 Z-22.5194
X39.7933 A161.1429 Z-22.3956
X39.2811 A159.0686 Z-22.3552
X38.1635 A154.5429 Z-22.3410
X26yue4ri753 A107.2114
X13.4832 A54.6000
X1.7949 A7.2686
X0.0254 A0.1029
X0.0720 A0.2914
X38.0238 A153.9771
X38.5360 A156.0514 Z-22.3488
X40.3056 A163.2171 Z-22.5317
X41.6560 A168.6857 Z-22.6340
X43.0530 A174.3429 Z-22.6978
X44.4500 A180.0000 Z-22.7201
X45.8936 A185.8457 Z-22.6983
X47.2906 A191.5029 Z-22.6351
X48.6410 A196.9714 Z-22.5333
X50.1311 A203.0057 Z-22.3757
X50.5968 A204.8914 Z-22.3433
X64.0080 A259.2000 Z-22.3410
X77.5123 A313.8857
X88.8746 A359.8972
X88.8280 A359.7086
X51.3419 A207.9086
X50.8296 A205.8343 Z-22.3646
X49.2464 A199.4229 Z-22.5512
X47.8959 A193.9543 Z-22.6702
X46yue4ri989 A188.2971 Z-22.7492
X45.0554 A182.4514 Z-22.7877
X43.6584 A176.7943 Z-22.7840
X42.2148 A170.9486 Z-22.7383
X40.8644 A165.4800 Z-22.6551
X39.5139 A160.0114 Z-22.5294
X38.4429 A155.6743 Z-22.4005
X37.9772 A153.7886 Z-22.3539
X36.7199 A148.6971 Z-22.3410
X24.4729 A99.1029
X11.2480 A45.5486
X0.0254 A0.1029
X0.0720 A0.2914
X37.1856 A150.5829
X37.6513 A152.4686 Z-22.3622
X39.2811 A159.0686 Z-22.5668
X40.5850 A164.3486 Z-22.6928

gold110

怎么没有人帮忙一下呢:em17:

yhzzp

用这个试试